Phased array ultrasonic testing of ‎offshore wind bolted flange ‎connections

Javadi, Yashar and Mills, Brandon and Pourrahimian Leilabadi, Parinaz and Nicolson, Ewan and Lotfian, Saeid and Zimermann, Rastislav and Abad, Farhad and Mehmanparast, Ali and MacLeod, Charles and Pierce, Gareth and Lines, David and Brennan, Feargal and Mehnen, Jorn and Gachagan, Anthony (2023) Phased array ultrasonic testing of ‎offshore wind bolted flange ‎connections. In: 50th Annual Review of Progress in Quantitative Nondestructive Evaluation, 2023-07-24 - 2023-07-27, Sheraton Austin Hotel at the Capitol,.

[thumbnail of Javadi-etal-QNDE-2023-Phased-array-ultrasonic-testing-of-offshore]
Preview
 Text. Filename: Javadi_etal_QNDE_2023_Phased_array_ultrasonic_testing_of_offshore.pdf
Accepted Author Manuscript
License: Strathprints license 1.0
Download (75kB)| Preview

Abstract

Offshore wind will play a key role in the majority of countries' plans to accelerate towards NetZero ‎‎‎and low-carbon energy transitions. Using fasteners (bolts and nuts) as a joining strategy is a ‎‎common ‎practice in various sections of the Offshore Wind Turbines (OWT) which needs regular ‎‎Non-‎Destructive Testing (NDT). For example, the bolted connection between the monopile and the ‎‎‎transition piece is under an immense stress concentration, which can result in loosening and even ‎‎‎failure of the connection. The current procedure to test the bolts involves fixed permanent strain ‎‎‎gauges and/or ultrasonic methods (using single-element transducers) to ensure the specific preload is ‎maintained during the wind turbine operation. In the case of using the strain gauge, the ‎‎challenge is the ‎number of bolts used in turbines in a wind farm, which can result in thousands of ‎‎required strain ‎gauges, and then as a usual practice, only a very limited number of bolts can only be ‎‎monitored.‎ The ultrasonic stress measurement technology is based on the acoustoelasticity theory, the relationship ‎between ‎the acoustic wave velocity and material stress, and the change in the ultrasonic Time of Flight ‎‎(ToF) corresponded ‎to the change in the length of the bolt due to the tightening axial force. This ‎process will then rely on the ‎calibration procedure including measurement of the acoustoelastic ‎coefficient and also the ToF in the free-stress ‎bolt. In the traditional ultrasonic method, the operator ‎uses single-element transducers and assumes ‎any difference between the ToF of a bolt in service and ‎the calibration bolt corresponds to the stress (pre-load) ‎change. While this assumption can be true for a ‎brand-new bolt, similar to what is used in the lab for calibration, it ‎will ignore corrosion, defects, ‎ageing, creep, strain-hardening, fatigue and other material changes during the ‎service life. In this paper, ‎the Phased Array Ultrasonic Testing (PAUT) system will be used instead of the single-element ‎approach. The ‎‎advantage of the PAUT system over the single-element transducer is the possibility of ‎‎(I) ‎defect detection and (II) ‎stress measurement, simultaneously. Combining the defect detection and ‎stress measurement is critical, ‎otherwise, the ultrasonic stress measurement and calibration procedure ‎will be influenced by the possible defects. ‎Using the PAUT and an array instead of a single-element ‎transducer, will allow the detection of the possible ‎defects in some of the specific acoustic paths used ‎for the ToF measurement and then use alternative acoustic ‎paths for the stress measurement. ‎Furthermore, advanced post-processing algorithms like Total Focusing Method ‎‎(TFM) can allow the ‎possibility of focusing ‎on more threads which are usually critical points of concern in the ‎safety-‎critical bolts.‎ It should also be noted that the bolt material used for offshore applications is usually ‎marine-grade high-alloy steel and/or stainless steel which can result in a poor Signal-to-Noise Ratio ‎‎(SNR) corresponding to the austenitic microstructure and large grain noise. In this paper, Phase ‎Coherence Imaging (PCI) was used to improve the SNR value in the PAUT bolt testing. PCI is an ‎amplitude-free synthetic beamforming method, ‎which considers the phase dispersion at each discrete ‎image point. This allows‎ incoherent noises ‎resulting from side lobes, grating lobes, reverberations and ‎grain noise to be reduced.‎ The experimental setup included an M20 bolt tested by a 10 MHz 32-element array (Olympus, ‎USA) ‎and FIToolbox phased array controller (Diagnostic Sonar, UK). A washer-shaped load cell ‎‎(BoltSafe, ‎Netherlands) was used to verify the ultrasonic stress measurement results. The PAUT stress ‎measurement system could successfully detect the ToF variations caused by the bolt’s stress change ‎recorded by the load cell. For defect ‎detection, two Side-Drilled Holes (SDH) were produced between ‎the threads to quantify the scanning image and SNR. The Full Matrix Capturing (FMC) was then ‎imported into a Matlab-programmed TFM and PCI code. The application of these advanced post-‎processing algorithms resulted in a clearer scanning image, improved SNR value and detection of the ‎SDHs with a lower gain.‎

ORCID iDs

Javadi, Yashar ORCID logoORCID: https://orcid.org/0000-0001-6003-7751, Mills, Brandon, Pourrahimian Leilabadi, Parinaz, Nicolson, Ewan, Lotfian, Saeid ORCID logoORCID: https://orcid.org/0000-0001-8542-933X, Zimermann, Rastislav, Abad, Farhad ORCID logoORCID: https://orcid.org/0000-0001-6765-8593, Mehmanparast, Ali ORCID logoORCID: https://orcid.org/0000-0002-7099-7956, MacLeod, Charles ORCID logoORCID: https://orcid.org/0000-0003-4364-9769, Pierce, Gareth ORCID logoORCID: https://orcid.org/0000-0003-0312-8766, Lines, David ORCID logoORCID: https://orcid.org/0000-0001-8538-2914, Brennan, Feargal ORCID logoORCID: https://orcid.org/0000-0003-0952-6167, Mehnen, Jorn ORCID logoORCID: https://orcid.org/0000-0001-6625-436X and Gachagan, Anthony ORCID logoORCID: https://orcid.org/0000-0002-9728-4120;
CORE (COnnecting REpositories)