Collaborative robotic Wire + Arc Additive Manufacture and sensor-enabled in-process ultrasonic Non-Destructive Evaluation

Tools

Zimermann, Rastislav and Mohseni, Ehsan and Vasilev, Momchil and Loukas, Charalampos and Vithanage, Randika K. W. and MacLeod, Charles N. and Lines, David and Javadi, Yashar and Espirindio E Silva, Misael Pimentel and Fitzpatrick, Stephen and Halavage, Steven and McKegney, Scott and Pierce, Stephen Gareth and Williams, Stewart and Ding, Jialuo (2022) Collaborative robotic Wire + Arc Additive Manufacture and sensor-enabled in-process ultrasonic Non-Destructive Evaluation. Sensors, 22 (11). 4203. ISSN 1424-8220 (https://doi.org/10.3390/s22114203)

[thumbnail of Zimermann-etal-Sensors-2022-Collaborative-robotic-wire-arc-additive-manufacture]
Preview
 Text. Filename: Zimermann_etal_Sensors_2022_Collaborative_robotic_wire_arc_additive_manufacture.pdf
Final Published Version
License: Creative Commons Attribution 4.0 logo
Download (1MB)| Preview

Abstract

The demand for cost-efficient manufacturing of complex metal components has driven research for metal Additive Manufacturing (AM) such as Wire + Arc Additive Manufacturing (WAAM). WAAM enables automated, time-and material-efficient manufacturing of metal parts. To strengthen these benefits, the demand for robotically deployed in-process Non-Destructive Evaluation (NDE) has risen, aiming to replace current manually deployed inspection techniques after completion of the part. This work presents a synchronized multi-robot WAAM and NDE cell aiming to achieve (1) defect detection in-process, (2) enable possible in-process repair and (3) prevent costly scrappage or rework of completed defective builds. The deployment of the NDE during a deposition process is achieved through real-time position control of robots based on sensor input. A novel high-temperature capable, dry-coupled phased array ultrasound transducer (PAUT) roller-probe device is used for the NDE inspection. The dry-coupled sensor is tailored for coupling with an as-built high-temperature WAAM surface at an applied force and speed. The demonstration of the novel ultrasound in-process defect detection approach, presented in this paper, was performed on a titanium WAAM straight sample containing an intentionally embedded tungsten tube reflectors with an internal diameter of 1.0 mm. The ultrasound data were acquired after a pre-specified layer, in-process, employing the Full Matrix Capture (FMC) technique for subsequent post-processing using the adaptive Total Focusing Method (TFM) imaging algorithm assisted by a surface reconstruction algorithm based on the Synthetic Aperture Focusing Technique (SAFT). The presented results show a sufficient signal-to-noise ratio. Therefore, a potential for early defect detection is achieved, directly strengthening the benefits of the AM process by enabling a possible in-process repair.

ORCID iDs

Zimermann, Rastislav, Mohseni, Ehsan ORCID logoORCID: https://orcid.org/0000-0002-0819-6592, Vasilev, Momchil, Loukas, Charalampos ORCID logoORCID: https://orcid.org/0000-0002-3465-8076, Vithanage, Randika K. W. ORCID logoORCID: https://orcid.org/0000-0002-1023-2564, MacLeod, Charles N. ORCID logoORCID: https://orcid.org/0000-0003-4364-9769, Lines, David ORCID logoORCID: https://orcid.org/0000-0001-8538-2914, Javadi, Yashar ORCID logoORCID: https://orcid.org/0000-0001-6003-7751, Espirindio E Silva, Misael Pimentel ORCID logoORCID: https://orcid.org/0000-0001-5927-643X, Fitzpatrick, Stephen ORCID logoORCID: https://orcid.org/0000-0002-3669-3262, Halavage, Steven, McKegney, Scott, Pierce, Stephen Gareth, Williams, Stewart and Ding, Jialuo;
CORE (COnnecting REpositories)